skip to main |
skip to sidebar
World-Markets-Now.COM
Terms
Tread
The tread is that portion of the tire that comes in contact with the road. The tread is a thick rubber compound formulated to provide a high level of traction that does not wear away too quickly. The tread pattern is characterized by the geometrical shape of the grooves, lugs, and voids. Grooves run circumferentially around the tire, and are needed to channel away water. Lugs are that portion of the tread design that contacts the road surface. Voids are spaces between lugs that allow the lugs to flex. Tread patterns feature non-symmetrical lug sizes circumferentially in order to minimize noise.
Treads are often designed to meet specific product marketing positions. High performance tires have small void ratios to provide more rubber in contact with the road for higher traction, but may be compounded with softer rubber that provides better traction, but wears quickly. Mud and snow tires are designed with higher void ratios to channel away rain and mud, while providing better gripping performance. When installing new tires, you should try and replace all four at once. Installing just two new tires on the front or rear will encourage under steer or over steer, depending on the vehicle and position of the new tires.
Snow tires are a very[citation needed] special kind of tire. They actually gain traction when it is cold, whereas, other tires lose traction on the ice and snowy roads.
Tread lug
Tread lugs provide the contact surface necessary to provide traction. As the tread lug enters the road contact area, or footprint, it is compressed. As it rotates through the footprint it is deformed circumferentially. As it exits the footprint, it recovers to its original shape. During the deformation and recovery cycle the tire exerts variable forces into the vehicle. These forces are described as Force Variation.
Tread void
Tread voids provide space for the lug to flex and deform as it enters and exits the footprint. Voids also provide channels for rainwater to flow out of the footprint. Voids also provide space for mud and snow to be channeled away from the footprint. The void ratio is the void area of the tire divided by the entire tread area. Low void areas have high contact area and therefore higher traction.
Rain groove
The rain groove is a design element of the tread pattern specifically arranged to channel water away from the footprint. Rain grooves are circumferential in most truck tires. Many high performance passenger tires feature rain grooves that are angled from the center toward the sides of the tire. Some tire manufacturers claim that their tread pattern is designed to actively pump water out from under the tire by the action of the tread flexing. This results in a smoother ride in different types of weather.
Sipe
Tread lugs often feature small narrow voids, or sipes, that improve the flexibility of the lug to deform as it traverses the footprint area. This reduces shear stress in the lug and reduces heat build up[citation needed]. Sipes also provide greater traction in icy conditions.
Wear bar
Wear bars are raised features located at the bottom of the tread grooves that indicate excessive tire wear. When the tread lugs are worn to the point that the wear bars connect across the lugs, the tires are fully worn and should be taken out of service.
Contact patch
The contact patch, or footprint, of the tire is the area of the tread in contact with the road. This is the area that transmits forces between the tire and the road via friction. The length-to-width ratio of the contact patch will affect steering and cornering behavior.
Bead
The bead is that part of the tire that contacts the wheel. The bead is reinforced with steel wire, and compounded from high strength, low flexibility rubber. The bead seats against the wheel tightly to ensure that the tire holds air without leakage. The bead fit is tight also to ensure the tire does not shift circumferentially as the tire rotates.
Sidewall
The sidewall is that part of the tire that bridges between the tread and bead. The sidewall is reinforced with rubber and fabric plies that provide for strength and flexibility. The sidewall transmits the torque applied by the drive axle to the tread in order to create traction. Sidewalls are molded with decorative ornamentation, government mandated warning labels, and other consumer information.
Over time, rubber degrades. Ford has recommended that tires be replaced when they are 6 years old to prevent sudden failure, even if the tire looks undamaged. In tropical climates, such as in Singapore, tires degrade sooner than in temperate climates.
Shoulder
The shoulder is that part of the tire at the edge of the tread as it makes transition to the sidewall
Inner tubeBicycle tires and some passenger and truck tires are designed for use with inner tubes. Inner tubes are torus shaped balloons made from a material impervious to air leakage. The inner tubes are inserted into the tire and inflated to give the tire its final shape.
Wheel
Tires are mounted to wheels, or rims, that bolt to the drive axle. Automotive wheels are either made from cast metal alloys, or stamped/welded metal. According to The Merriam's Webster Dictionary the rim is the outer part of the wheel, the tire does mount to the rim but a rim is not a wheel
Valve stem
The valve stem is a tubular rubber shape with a metal valve used to inflate the tire with air. Valve stems usually protrude through the wheel for easy access for inflation. Tires are inflated through a valve, typically a Schrader valve on automobiles and most bicycle tires, or a Presta valve on high performance bicycles. The rubber in valve stems eventually degrades. Replacement of the valve stem at regular intervals reduces the chance of failure.
Tire pressure monitoring system
Tire pressure monitoring systems are electronic systems that continuously monitor tire pressure on a vehicle, and alarm when the pressure goes below a warning limit. There are several types of designs to monitor tire pressure. Some actually measure the air pressure and some make indirect measurements, such as gauging when the relative size of the tire changes due to lower air pressure. These systems are becoming mandatory in countries such as the United States.
Load rating
Tires are specified by the manufacturer with a maximum load rating. Loads exceeding the rating can result in unsafe conditions that can lead to steering instability and even rupture. For a table of load ratings, see tire codes.
Inflation pressure
Tires are specified by the manufacturer with a recommended inflation pressure that permits safe operation within the specified load rating. Most tires are stamped with a maximum pressure rating. For passenger vehicles and light trucks, the tires should be inflated to what the vehicle manufacturer specifies, which is usually located on a decal just inside the driver's door.
Speed rating
The speed rating denotes the maximum speed at which a tire is designed to be driven for extended periods of time. The ratings range from 99 mph (160 km/h) to 186 mph (300 km/h). For a table of speed ratings, see tire code.
Rotation
Tires do often exhibit irregular wear patterns once installed on a vehicle and partially worn. Tire rotation is the procedure of moving tires to different car positions, such as front-to-rear, in order to even out the wear, thereby extending the life of the tire.
Wheel alignment
Once mounted on the vehicle, the tire may not be perfectly aligned to the direction of travel, and therefore exhibit irregular wear, often quite substantial. A wheel alignment is the procedure for checking and correcting this condition through adjustment of camber, caster and toe angles. These settings also affect the handling characteristics of the vehicle.
Retread
Tires that are fully worn can be re-manufactured to replace the worn tread. Retreading is the process of buffing away the worn tread and applying a new tread. Retreading is economical for truck tires because the cost of the replacement is small compared to the cost of the tire carcass. Retreading is less economical for passenger tires because the cost is high compared to the cost of a new tire.
Flat
A flat tire occurs when the tire deflates to the point that the metal of the wheel comes to ground level. This can occur as a result of a wear-and-tear, a leak, or more serious damage. A flat tire seriously impairs the ability of the vehicle to be driven, requiring the vehicle to be safely removed from the road, and the tire to be changed. Continuing to drive a vehicle with a flat tire may result in damage to the tire or the vehicle, and may put the occupants and other vehicles in danger.
Hydroplaning (or aquaplaning)
Hydroplaning, also known as aquaplaning, is the condition where a layer of water is present between the tire and road. Hydroplaning occurs when the tread pattern cannot channel away water at an adequate speed to ensure a complete dry footprint area. When hydroplaning occurs the tire loses traction and steering, and creates a very unsafe driving condition. When hydroplaning occurs, there is less responsiveness of the steering wheel. The correction of this unsafe condition is to gradually reduce speed.
The tread is that portion of the tire that comes in contact with the road. The tread is a thick rubber compound formulated to provide a high level of traction that does not wear away too quickly. The tread pattern is characterized by the geometrical shape of the grooves, lugs, and voids. Grooves run circumferentially around the tire, and are needed to channel away water. Lugs are that portion of the tread design that contacts the road surface. Voids are spaces between lugs that allow the lugs to flex. Tread patterns feature non-symmetrical lug sizes circumferentially in order to minimize noise.
Treads are often designed to meet specific product marketing positions. High performance tires have small void ratios to provide more rubber in contact with the road for higher traction, but may be compounded with softer rubber that provides better traction, but wears quickly. Mud and snow tires are designed with higher void ratios to channel away rain and mud, while providing better gripping performance. When installing new tires, you should try and replace all four at once. Installing just two new tires on the front or rear will encourage under steer or over steer, depending on the vehicle and position of the new tires.
Snow tires are a very[citation needed] special kind of tire. They actually gain traction when it is cold, whereas, other tires lose traction on the ice and snowy roads.
Tread lug
Tread lugs provide the contact surface necessary to provide traction. As the tread lug enters the road contact area, or footprint, it is compressed. As it rotates through the footprint it is deformed circumferentially. As it exits the footprint, it recovers to its original shape. During the deformation and recovery cycle the tire exerts variable forces into the vehicle. These forces are described as Force Variation.
Tread void
Tread voids provide space for the lug to flex and deform as it enters and exits the footprint. Voids also provide channels for rainwater to flow out of the footprint. Voids also provide space for mud and snow to be channeled away from the footprint. The void ratio is the void area of the tire divided by the entire tread area. Low void areas have high contact area and therefore higher traction.
Rain groove
The rain groove is a design element of the tread pattern specifically arranged to channel water away from the footprint. Rain grooves are circumferential in most truck tires. Many high performance passenger tires feature rain grooves that are angled from the center toward the sides of the tire. Some tire manufacturers claim that their tread pattern is designed to actively pump water out from under the tire by the action of the tread flexing. This results in a smoother ride in different types of weather.
Sipe
Tread lugs often feature small narrow voids, or sipes, that improve the flexibility of the lug to deform as it traverses the footprint area. This reduces shear stress in the lug and reduces heat build up[citation needed]. Sipes also provide greater traction in icy conditions.
Wear bar
Wear bars are raised features located at the bottom of the tread grooves that indicate excessive tire wear. When the tread lugs are worn to the point that the wear bars connect across the lugs, the tires are fully worn and should be taken out of service.
Contact patch
The contact patch, or footprint, of the tire is the area of the tread in contact with the road. This is the area that transmits forces between the tire and the road via friction. The length-to-width ratio of the contact patch will affect steering and cornering behavior.
Bead
The bead is that part of the tire that contacts the wheel. The bead is reinforced with steel wire, and compounded from high strength, low flexibility rubber. The bead seats against the wheel tightly to ensure that the tire holds air without leakage. The bead fit is tight also to ensure the tire does not shift circumferentially as the tire rotates.
Sidewall
The sidewall is that part of the tire that bridges between the tread and bead. The sidewall is reinforced with rubber and fabric plies that provide for strength and flexibility. The sidewall transmits the torque applied by the drive axle to the tread in order to create traction. Sidewalls are molded with decorative ornamentation, government mandated warning labels, and other consumer information.
Over time, rubber degrades. Ford has recommended that tires be replaced when they are 6 years old to prevent sudden failure, even if the tire looks undamaged. In tropical climates, such as in Singapore, tires degrade sooner than in temperate climates.
Shoulder
The shoulder is that part of the tire at the edge of the tread as it makes transition to the sidewall
Inner tubeBicycle tires and some passenger and truck tires are designed for use with inner tubes. Inner tubes are torus shaped balloons made from a material impervious to air leakage. The inner tubes are inserted into the tire and inflated to give the tire its final shape.
Wheel
Tires are mounted to wheels, or rims, that bolt to the drive axle. Automotive wheels are either made from cast metal alloys, or stamped/welded metal. According to The Merriam's Webster Dictionary the rim is the outer part of the wheel, the tire does mount to the rim but a rim is not a wheel
Valve stem
The valve stem is a tubular rubber shape with a metal valve used to inflate the tire with air. Valve stems usually protrude through the wheel for easy access for inflation. Tires are inflated through a valve, typically a Schrader valve on automobiles and most bicycle tires, or a Presta valve on high performance bicycles. The rubber in valve stems eventually degrades. Replacement of the valve stem at regular intervals reduces the chance of failure.
Tire pressure monitoring system
Tire pressure monitoring systems are electronic systems that continuously monitor tire pressure on a vehicle, and alarm when the pressure goes below a warning limit. There are several types of designs to monitor tire pressure. Some actually measure the air pressure and some make indirect measurements, such as gauging when the relative size of the tire changes due to lower air pressure. These systems are becoming mandatory in countries such as the United States.
Load rating
Tires are specified by the manufacturer with a maximum load rating. Loads exceeding the rating can result in unsafe conditions that can lead to steering instability and even rupture. For a table of load ratings, see tire codes.
Inflation pressure
Tires are specified by the manufacturer with a recommended inflation pressure that permits safe operation within the specified load rating. Most tires are stamped with a maximum pressure rating. For passenger vehicles and light trucks, the tires should be inflated to what the vehicle manufacturer specifies, which is usually located on a decal just inside the driver's door.
Speed rating
The speed rating denotes the maximum speed at which a tire is designed to be driven for extended periods of time. The ratings range from 99 mph (160 km/h) to 186 mph (300 km/h). For a table of speed ratings, see tire code.
Rotation
Tires do often exhibit irregular wear patterns once installed on a vehicle and partially worn. Tire rotation is the procedure of moving tires to different car positions, such as front-to-rear, in order to even out the wear, thereby extending the life of the tire.
Wheel alignment
Once mounted on the vehicle, the tire may not be perfectly aligned to the direction of travel, and therefore exhibit irregular wear, often quite substantial. A wheel alignment is the procedure for checking and correcting this condition through adjustment of camber, caster and toe angles. These settings also affect the handling characteristics of the vehicle.
Retread
Tires that are fully worn can be re-manufactured to replace the worn tread. Retreading is the process of buffing away the worn tread and applying a new tread. Retreading is economical for truck tires because the cost of the replacement is small compared to the cost of the tire carcass. Retreading is less economical for passenger tires because the cost is high compared to the cost of a new tire.
Flat
A flat tire occurs when the tire deflates to the point that the metal of the wheel comes to ground level. This can occur as a result of a wear-and-tear, a leak, or more serious damage. A flat tire seriously impairs the ability of the vehicle to be driven, requiring the vehicle to be safely removed from the road, and the tire to be changed. Continuing to drive a vehicle with a flat tire may result in damage to the tire or the vehicle, and may put the occupants and other vehicles in danger.
Hydroplaning (or aquaplaning)
Hydroplaning, also known as aquaplaning, is the condition where a layer of water is present between the tire and road. Hydroplaning occurs when the tread pattern cannot channel away water at an adequate speed to ensure a complete dry footprint area. When hydroplaning occurs the tire loses traction and steering, and creates a very unsafe driving condition. When hydroplaning occurs, there is less responsiveness of the steering wheel. The correction of this unsafe condition is to gradually reduce speed.
Blog Archive
Blog Sites Links,
Pregnancy Talk,
Pregnancy Walks,
Pregnancy 9,
Pregnant Signs,
Pregnant Nine,
Pregnancy-9,
4ty Weeks,
Lottery Links,
Lotto Links,
Lottery Link,
Lottery Post,
Lottery Link,
Chinese Job,
African Job,
Africa Job,
African Jobs Home,
American Job Market,
American Jobs,
UK Job Finder,
European Job Market,
European Jobs,
American Jobs Markets,
Taiwan Tobs,
UK Job Markets,
Predictions of Nostradamus,
Consultant Gynaecologist,
Indian Job Finder,
Indian Government Jobs,
Jobs in Russia,
Russian Job,
Asian Job,
Job Asia,
Job in German,
Chinese Job Market,
Chinese Job Market,
www.ez2.me,
Linkque,
Gynaecologist Consultant,
Fashion Host,
Housing Aid,
Pheap Plane,
NFL Play,
Oil Finder,
You Are Smarter,
Fashions Finder,
Steel Finder,
Machinery Finder,
Engineer Finder,
CNC Machinery,
CNC Machin,
Machinery Exportersr,
Easy Dot,
Oil Biz,
NY Movers,
Link Que,
www.east2.me,
Easy Race,
I Reporters,
Shrinking Atlantic,
Used Machinery Finderr,
Real Machinery,
Oil Reserves,
Pakistan Loadshedding,
KESCr,
e Widget,
e-Bay,
Advertise,
Media Tower,
Itwar Bazar,
Gardens Gadgets,
Sport Gadgets,
Garden Gadget,
China Finder,
Gadgets Garden,
Gadgets Finder,
American Gadgets,
World Fuel,
BoolyWood Stars,
Gadgets Gardens,
Gadgets Find,
Shopping Gadget,
Lottery Predictions,
Urdu Campus,
Predictions of Future,
China Finder,
Advertise in 690 Blogs,
Future Predictions,
Lottery Predictions,
BoolyWood Stars,
European Job Market,
India Job Finder,
Predictions of Nostradamus,
Chamak Damk Jobs,
Gaza Today,
Son of Bush,
HumTum.Me,
China Trade Homes,
Export Import Finder,
Good By Mr Bush,
American Enemy,
Enemies of American,
Enemy of USA,
Universe Enemy,
Easy to Me,
Enemies of World,
easy 2 Me,
Buy Sell Rent,
Finance Finder,
You Finder,
Wine Finder,
Shaadi Finder,
Great Hall,
Made in China,
EDU Fider,
Machinery Importers,
China Machinery,
Olympic Finder,
France Finder,
Miss Finder,
Star Finder,
Trip Finder,
Hong Kong Race,
US Finder,
Incredible India,
India Finder,
KESCr,
Foxfinder,
Basmati Finder,
Dollar Finder,
Find Euro,
Business Hub,
UN Mission,
Rahulghandi Discover India,
Cargo Line,
Business Admin,
Fuel Business,
Education Finder,
Swiss Finder,
Tea Finder,
Consultant Gynaecologis,
UK Finder,
World Fuel,
BoolyWood Stars,
China Finder,
Gwadar,
Transatlantic Travel,
US State Police,
Made in Taiwan,
Taiwan Machinery,
Bill clinton,
Change we Can,
HoolyWood Stars,
Chine Trade,
Sunday Bazar,
Media Politics,
Beijing Gold,
Econo India,
Dream Liner,
Super A380,
World Markets Now,
World Markets Now,
Easy to Me,
Easy 2 Me,
Easy For Me,
Ez For Me,
Valentine America,
ValentineAmerica,
Your Valentine Shop,
Valentine Shop,
My Valentine Shop,
My Valentine,
Valentine Town,
Valentine Hall,
Valentinehall,
Valentine Star,
Gift Shopping,
Valentine Gift,
Shopping,
Valentine Shopping,
Valentine Stores,
Super Stores,
Valentine Store,
Smart Store,
Valentine Friendship,
Used Machinery,
Valentine Friends,
Valentine Date,
Valentine Host,
valentine world,
valentine-in-france,
Media Politics,
Valentine France,
Valentine China,
Valentine of China,
Job Cutting,
Housing Sport,
World Mostpo Pular Events,
Popular Events 2009,
Most Popular Places,
Popular Places,
Tallest Towers,
Most Tallest Towers,
Buildings,
Tallest Buildings,
Valentine Works,
Valentine Report,
Indian Valentine,
Spanish Valentine,
Valentine Market,
Valentines Day,
Food Markets,
Top Food,
Point Politics,
Department of Job,
Finance Department,
Your Department,
New Department,
Public Department,
World Department,
Sell Department,
Advertise More,
Tourism Department,
Culture Department,
Autos Department,
Fashion Department,
Commercial Department,
Search All,
Host Gateway,
Host Finder,
Web Hosting,
Server Provider,
Server School,
Server New
Server System,
Domain System,
Host Guru,
Host China,
Host America,
Hosting America,
Server USA,
Hosting America,
America Hosting,
Hosting Support,
Host Counter,
Top Web Com,
Find For Hosting,
Hosting Bot,
Valentine Ready,
Ready Valentine,
Shopping For Valentine,
Shop Of Valentine,
Shopping Valentine,
Shop Valentine,
Top Web valentine,
Store For Valentine,
World of Valentine,
World Valentine,
valentine Support,
World Valentines Day,
Valentineine World,
My Valentine world,
Discount Again,
Tourdfrance,
Metro of London,
Indian Metro,
Tour De France,
You Are Smarter,
Metro of Moscow,
Sunday Jobs,
Narth Dollar,
Wasted Dollar,
Dollar Waste,
Sunday Earning,
My Sunday Friends,
Indian Metro,
Metro of Tokyo,
How Make Gadgetss,
How Works Gadgets,
Gadgets Mail,
Mail Gadgets,
Click Gadgets,
Gadgets Comparison,
Howgad Getsworks,
Dollar Day,
Earn Seven Day,
Earn 7 Day,
Earn Every Day,
Earn Sunday,
World Forcesr,
Naval Forces,
Drive Sign,
XX 20 Cricket,
20 XX Cricket,
More Then 600 Blog,
Exchange Sunday,
Sunday Exchange,
Michelle Obama Now,
Who Will be Prime Minister of India,
BBC,
Live and Work Canada,
Work And Study in America,
Work and Study in UK,
Live and work in Newzealand,
99 Cent Per Post,
Live and Work in USA,
Live and Work in UK,
Live and Work in Australia,
Visit of America Now,
Miss Sunday,
Sunday Miss,
Search Hard,
Russia Finder,
Allday Search,
Search Sunday,
Search for Sunday,
Sunday Busy,
Gadgets Shopping,
Finance Gadgets,/a>
Geo Gadgets,
Forex Gadgets,
Gadgets Car,
Gadgets Shoppers,
Financial Gadget,/a>
First Fadgets,
Sunday Gadgets,
First Gadget,
Morning Gadgets,
Night Gadgets,
Dr. Dhahid Masood,
A to Z Railways,
A to Z Airports,
A to Z Airlines,
World Coast Guards,
World Naval Forces,
World Armed Forces,
Naval Forces,
Inter Fare,
World Air Forces,
Forbes,
Who Will be Next Prime Minister of India,
President Cabinet,
Broadband Problems,
360 of A380,
Heathrow Airport,
Narita Airport,
Tower of Tokyo,
Inter Fare,
Vancouver 2010,
London 2012,
Sharmel Sheikh,
US President Cabinet,
World Markets Now,
World Markets,
Trip Trick,
Top-10-Broadband,
360 of A-380,
Xmas Discount,
Skin Talks,
top broadband,
Start Park,
Narth America Today,
My Stalin,
VOA Now,
Great Lenin,
Trip Finder,
5 Links a Day,
Son of Bush,
Jobs in Japan,
UK Gadget,
Gadget Sart,
Arts Gadgets,
Hit My Link,
Department of Tourism,
Click My Choice,
Hit My Web,
Department of Pets,
Communication Department,
Authority of Communication,
US Department of States,
Department of Money,
Alaska 2010,
Advertise our 700 Blogs,
Global Car Crisis,
Car Tribal Time,
Blogs Departmen,
Money Groups,
Blogging Terms,
Blog Terms,
Terms Time,
Times Tracker,
Tracker Time,
Time Wap,
Wish Track,
Wish Talk,
Wish Your Dreams,
Your Dream Wish,
My Dreams Wish,
Color Groups,
Colors Groups,
Department of Highway,
Wap Time,
Email Check,
Email Click,
Inbox Click,
Affiliate Counter,
Click Linker,
Mr Affiliates,
Prisoner Friends,
Youtube Affiliate,
Affiliate Video Tour,
House Based Affiliate,
5 DPR Alaska,
Night Moons,
Taj Mahal Birthday,
Taj Mahal Anniversary,
Taj Mahal 350,
350 Taj Mahal,
Department of Food,
Department of Music,
Career Based Websites,
Career Based Jobs,
Career Based,
WWW.eZ2.Me,
WWW.easy2.Me,
www.easy2.Me,
Gen Pervez Musharraf,
Iftikhar Muhammad Chaudhry,
Mian Muhammad Shahbaz Sharif,
Mian Muhammad Nawaz Sharif,
President Asifali Zardari,
bilawal Bhutto Zardari,
Chaudhry Shujaat Hussain,
Chaudhry Iftikhar Muhammad,
Alaskan Independence Party,
Department of States,
US Department of state,
Blog Based,
My Health Need,
Your Health Need,
My Health Front,
Careers Front,
Sri Lanka Cricket,
Worldwid Wealth,D
department of Children,
Department of Money,
Department of treasury,
Treasury Department,
Money Department,
Weather Department,
Music Administration,
Department of Sex,
Department of Fishing,
Department of Fish,
Department of Art,
Department of Business,
Hit My Page,
US Treasury Department,
Hit My Choice,
List of tire companies
1843 – Charles Goodyear announces vulcanization
1846 – Robert William Thomson invented and patented the pneumatic tire
1870 – BFGoodrich founded
1871 – Continental AG founded
1888 – First commercial pneumatic bicycle tire produced by Dunlop 1888 – Michelin Tire Company founded
1889 – Dunlop Tire Company founded
1889 – John Boyd Dunlop patented the pneumatic tire in the UK
1890 – Dunlop and William Harvey Du Cros began production of pneumatic tires in Ireland
1890 – Bartlett Clincher rim introduced
1891 – Dunlop's patent invalidated in favor of Thomson’s patent 1892 – Beaded edge tires introduced in the U.S.
1894 - E.J. Pennington invents the first balloon tire
1895 – Michelin introduced pneumatic automobile tires 1898 – Schrader valve stem patented
1898 – Goodyear Tire and Rubber Company founded 1900 – Firestone Tire & Rubber founded
1900 – Cord Tires introduced by Palmer (England) and BFGoodrich (U.S.)
1903 – Goodyear Tire Company patented the first tubeless tire, however it was not introduced until
1954 1904 – Goodyear and Firestone started producing cord reinforced tires
1904 – Mountable rims were introduced that allowed drivers to fix their own flats
1906 – First pneumatic aircraft tire
1908 – Frank Seiberling invented grooved tires with improved road traction
1910 – BFGoodrich Company invented longer life tires by adding carbon to the rubber
1917 – Yokohama Rubber Company founded
1919 – Goodyear and Dunlop announced pneumatic truck tires
1931 - Bridgestone Tire Co. Ltd. founded by Shojiro Ishibashi (Ishibashi means "stone bridge")
1938 – Goodyear introduced the rayon cord tire
1940 – BFGoodrich introduced the first commercial synthetic rubber tire 1946 – Michelin introduced the radial tire
1947 – Goodyear introduced first nylon tires
1947 – BFGoodrich introduced the tubeless tire
1963 – Use of polyester cord introduced by Goodyear
1965 – Armstrong Rubber introduced the bias belted fiberglass tire
1965 – BFGoodrich offered the first radial available in North America 1967 – Poly/glass tires introduced by Firestone and Goodyear
1968 – United States Department of Transportation (DOT) numbers required on new tires in USA
1974 - Pirelli introduced the wide radial tire, which is the international standard in tires today
1986 – BF Goodrich merged with Uniroyal to form Uniroyal-Goodrich 1987 – General Tire acquired by Continental 1988 – Firestone acquired by Bridgestone
1988 – Uniroyal-Goodrich acquired by Michelin
1999 – Goodyear acquired certain Dunlop tire factories from Sumitomo Rubber Industries
2005 – Pneuhage and Continental introduced first factory for tire services (aftermarket (automotive))
2006 – Bridgestone acquired Bandag (retread maker) For a list of tire companies and the dates they were established, see List of Tire Companies.
1846 – Robert William Thomson invented and patented the pneumatic tire
1870 – BFGoodrich founded
1871 – Continental AG founded
1888 – First commercial pneumatic bicycle tire produced by Dunlop 1888 – Michelin Tire Company founded
1889 – Dunlop Tire Company founded
1889 – John Boyd Dunlop patented the pneumatic tire in the UK
1890 – Dunlop and William Harvey Du Cros began production of pneumatic tires in Ireland
1890 – Bartlett Clincher rim introduced
1891 – Dunlop's patent invalidated in favor of Thomson’s patent 1892 – Beaded edge tires introduced in the U.S.
1894 - E.J. Pennington invents the first balloon tire
1895 – Michelin introduced pneumatic automobile tires 1898 – Schrader valve stem patented
1898 – Goodyear Tire and Rubber Company founded 1900 – Firestone Tire & Rubber founded
1900 – Cord Tires introduced by Palmer (England) and BFGoodrich (U.S.)
1903 – Goodyear Tire Company patented the first tubeless tire, however it was not introduced until
1954 1904 – Goodyear and Firestone started producing cord reinforced tires
1904 – Mountable rims were introduced that allowed drivers to fix their own flats
1906 – First pneumatic aircraft tire
1908 – Frank Seiberling invented grooved tires with improved road traction
1910 – BFGoodrich Company invented longer life tires by adding carbon to the rubber
1917 – Yokohama Rubber Company founded
1919 – Goodyear and Dunlop announced pneumatic truck tires
1931 - Bridgestone Tire Co. Ltd. founded by Shojiro Ishibashi (Ishibashi means "stone bridge")
1938 – Goodyear introduced the rayon cord tire
1940 – BFGoodrich introduced the first commercial synthetic rubber tire 1946 – Michelin introduced the radial tire
1947 – Goodyear introduced first nylon tires
1947 – BFGoodrich introduced the tubeless tire
1963 – Use of polyester cord introduced by Goodyear
1965 – Armstrong Rubber introduced the bias belted fiberglass tire
1965 – BFGoodrich offered the first radial available in North America 1967 – Poly/glass tires introduced by Firestone and Goodyear
1968 – United States Department of Transportation (DOT) numbers required on new tires in USA
1974 - Pirelli introduced the wide radial tire, which is the international standard in tires today
1986 – BF Goodrich merged with Uniroyal to form Uniroyal-Goodrich 1987 – General Tire acquired by Continental 1988 – Firestone acquired by Bridgestone
1988 – Uniroyal-Goodrich acquired by Michelin
1999 – Goodyear acquired certain Dunlop tire factories from Sumitomo Rubber Industries
2005 – Pneuhage and Continental introduced first factory for tire services (aftermarket (automotive))
2006 – Bridgestone acquired Bandag (retread maker) For a list of tire companies and the dates they were established, see List of Tire Companies.
No comments:
Post a Comment